1. If the shutdown time is more than 7 days, the nozzle needs to be cleaned and moisturized. It is necessary to empty all the ink inside the nozzle, use UV special cleaning solution, inject the cleaning solution from the ink inlet into the nozzle, and then discharge it from the ink discharge end inside the nozzle, and To let a part of the cleaning liquid be discharged from the nozzle, it is necessary to use enough cleaning liquid to clean the previous ink. Observe that the discharged cleaning liquid is transparent, and then use the needle to empty all the cleaning liquid inside the nozzle to ensure that the inside of the nozzle is completely empty. No cleaning fluid remains.
When the cleaning solution is emptied, screw on the plug, and then slowly inject the special nozzle moisturizing liquid, and the moisturizing liquid will flow out from the nozzle into water droplets (Note: the pressure should not be too large, otherwise the nozzle will be damaged)
After injecting the moisturizing liquid, quickly insert the ink tube into the ink valve to ensure that the ink valve of the secondary ink cartridge is closed to ensure the tightness, and then wrap the acrylic with plastic wrap for 8-10 circles, and pour an appropriate amount of moisturizing liquid on the plastic wrap. , press the trolley to the plastic wrap and touch it
Preparation before maintenance
Supplies preparation: 1 roll of plastic wrap, 1L of cleaning solution, 1L of moisturizing solution, 1 pair of disposable gloves, 2 disposable cups, 2 acrylic plates, 1 50ML syringe, 6*4 ink tube 20 cm. (The amount of cleaning solution is determined by the number of nozzles, be sure to clean it)
Precautions for cleaning the nozzle
1. The method of emptying the ink of the print head: use an unused 50ML disposable syringe when cleaning the print head, remove the connecting ink tube at the lower end of the secondary ink cartridge with scissors, open the plug at the exhaust pipe of the print head, and then use a syringe to remove the inside of the print head. Empty the ink first (Note: When cleaning, the nozzle terminals and cables cannot stick to the cleaning liquid, so protect them in advance)
2. To clean the nozzle, use a 6*4 ink tube to suck a syringe of cleaning liquid, then slowly inject it from the ink inlet end, and then discharge it, repeat 3-4 times, and observe that the cleaning liquid discharged from the nozzle and the ink discharge port is transparent. , and then use the needle to empty all the cleaning liquid inside the nozzle to ensure that no cleaning liquid remains in the nozzle.
3. After the cleaning liquid is drained, screw on the plug, and then slowly inject the special nozzle moisturizing liquid from the ink inlet, and discharge the moisturizing liquid from the nozzle surface in the form of water droplets, and then quickly insert the ink tube back into the secondary ink cartridge to ensure that the ink cartridge is Valve is closed.
4. Print the test strip before using the plastic wrap to clean the nozzle and archive. Ensure that the nozzle is in good condition
Wind the acrylic sheet flat for more than 8 layers, then pour an appropriate amount of moisturizing liquid, move the head of the car to the machine platform and lower the nozzle to lightly press on the plastic wrap to moisturize (refer to the video below for details), and finally turn off the main power of the device and cover it with a shading cloth Protect the front of the car from dust and light.
翻译结1. If the shutdown time is more than 7 days, the nozzle needs to be cleaned and moisturized. It is necessary to empty all the ink inside the nozzle, use UV special cleaning solution, inject the cleaning solution from the ink inlet into the nozzle, and then discharge it from the ink discharge end inside the nozzle, and To let a part of the cleaning liquid be discharged from the nozzle, it is necessary to use enough cleaning liquid to clean the previous ink. Observe that the discharged cleaning liquid is transparent, and then use the needle to empty all the cleaning liquid inside the nozzle to ensure that the inside of the nozzle is completely empty. No cleaning fluid remains. When the cleaning solution is emptied, screw on the plug, and then slowly inject the special nozzle moisturizing liquid, and the moisturizing liquid will flow out from the nozzle into water droplets (Note: the pressure should not be too large, otherwise the nozzle will be damaged) After injecting the moisturizing liquid, quickly insert the ink tube into the ink valve to ensure that the ink valve of the secondary ink cartridge is closed to ensure the tightness, and then wrap the acrylic with plastic wrap for 8-10 circles, and pour an appropriate amount of moisturizing liquid on the plastic wrap. , press the trolley to the plastic wrap and touch it 7. Preparation before maintenance Supplies preparation: 1 roll of plastic wrap, 1L of cleaning solution, 1L of moisturizing solution, 1 pair of disposable gloves, 2 disposable cups, 2 acrylic plates, 1 50ML syringe, 6*4 ink tube 20 cm. (The amount of cleaning solution is determined by the number of nozzles, be sure to clean it) Precautions for cleaning the nozzle 1. The method of emptying the ink of the print head: use an unused 50ML disposable syringe when cleaning the print head, remove the connecting ink tube at the lower end of the secondary ink cartridge with scissors, open the plug at the exhaust pipe of the print head, and then use a syringe to remove the inside of the print head. Empty the ink first (Note: When cleaning, the nozzle terminals and cables cannot stick to the cleaning liquid, so protect them in advance) 2. To clean the nozzle, use a 6*4 ink tube to suck a syringe of cleaning liquid, then slowly inject it from the ink inlet end, and then discharge it, repeat 3-4 times, and observe that the cleaning liquid discharged from the nozzle and the ink discharge port is transparent. , and then use the needle to empty all the cleaning liquid inside the nozzle to ensure that no cleaning liquid remains in the nozzle. 3. After the cleaning liquid is drained, screw on the plug, and then slowly inject the special nozzle moisturizing liquid from the ink inlet, and discharge the moisturizing liquid from the nozzle surface in the form of water droplets, and then quickly insert the ink tube back into the secondary ink cartridge to ensure that the ink cartridge is Valve is closed. 4. Print the test strip before using the plastic wrap to clean the nozzle and archive. Ensure that the nozzle is in good condition Wind the acrylic sheet flat for more than 8 layers, then pour an appropriate amount of moisturizing liquid, move the head of the car to the machine platform and lower the nozzle to lightly press on the plastic wrap to moisturize (refer to the video below for details), and finally turn off the main power of the device and cover it with a shading cloth Protect the front of the car from dust and light.
